'adaptec'에 해당하는 글 1건

레이드 구성시 Build/Verify 선택하여 진행후 바로 리부팅하여 하드를 사용을 한다.
clear 선택시는 레이드가 complete 되어야 사용가능하다. quick init 은 비권장이다.
나중에 하드 문제 발생할 경우 문제가 발생한다.

What is the difference between Build / Verify, Clear, Quick Init and Skip Init when creating an array using one of the listed RAID controllers? 

This information applies to the following Operating System(s): 
- This information is not Operating System specific
When creating a redundant RAID array using one of the HostRAID controllers (1220SA, 1225SA, 1420SA, 1430SA, 44300, 48300, 58300) listed, there are 3 choices for the Build method: 
- Build / Verify 
- Clear 
- Quick Init 

When creating a redundant RAID array using one of the Hardware RAID controllers listed, there are 4 choices for the Build method: 
- Build / Verify 
- Clear 
- Quick Init 
- Skip Init 

The differences between these options are listed below. If unsure of which option to use, it is recommended to choose "Build / Verify". 

Build / Verify 
  • Array is available for use immediately. The Build operation continues in the background. Therefore, an operating system installation may begin while the array is going through the Build process, although performance will be impacted until the process has completed.
  • Creates parity/redundancy for each disk in the array. Example: For a RAID 1 logical drive, data is copied from the source drive to the mirrored drive. For RAID 5 and RAID 6, parity is computed and written.
  • A Build can take up to 20x longer than Clear (due to parity generation).

  • Array is not available to use until the operation completes.
  • Fastest way to set the disks into a known good state.
  • Writes only zeroes to the disk. 
    Although no real redundancy/parity is created, all disk sectors contain zeroes (no data) so none is required. Any future write operations will create required redundancy.

Quick Init 
  • Array is available for use immediately.
  • Only creates metadata on member disks of the array, the build process is bypassed, the first few and last blocks in the user addressable area (incl. partition tables) will be wiped off. While this is the fastest method for creating a RAID array, it is only recommended for use with new drives. Performance will be impacted while the logical drive is in Quick Init mode until a Verify with Fix is performed from the Adaptec / ICP Storage Manager software.
  • For striped arrays (such as RAID 0, RAID 10, RAID 50, RAID 60), write performance is affected when less than a full stripe is written. The array remains in full-stripe write mode until a Verify with fix operation is completed to validate redundant information.
  • Default Setting for RAID 1, RAID 1EE, and RAID 10 arrays.

Skip Init 
  • Updates metadata only.
  • If multiple disk drives fail in the same logical device, it may be possible to recover the data by recreating the logical device without the initialization step (skip init). Omitting the initialization step reconstructs the logical device metadata without modifying or destroying other data on the disks.
  • Not available on HostRAID (1220SA, 1225SA, 1420SA, 1430SA, 44300, 48300, 58300) controllers.

'서버관리' 카테고리의 다른 글

하드 모델명 확인  (0) 2012.12.14
불법 접근 차단하기  (0) 2012.12.13
Adaptec Raid Controller Build options  (0) 2012.12.13
취약한 cgi 프로그램 perl 예시  (0) 2012.12.13
아파치 모듈 확인하기  (0) 2012.12.12
로그 파일에 대해  (0) 2012.12.12

유용했던 자료를 기록해 두었습니다. 도움이 되시길~~~ Welcome! I started this blog as a way to give back to all of the other system administrators who have taught me something in the past. Writing these posts brings me a lot of enjoyment and I hope you fun

받은 트랙백이 없고 , 댓글이 없습니다.